Photoelectron Holographic Study for Atomic Site Occupancy for Si Dopants in Si-Doped κ-Ga2O3(001).

We investigated atomic site occupancy for the Si dopant in Si-doped κ-Ga2O3(001) using photoelectron spectroscopy (PES) and photoelectron holography (PEH). From PES and PEH, we found that the Si dopant had one chemical state, and three types of inequivalent Si substitutional sites (SiGa) were formed. The ratios for the inequivalent tetrahedral, pentahedral, and octahedral SiGa sites were estimated to be 55.0%, 28.1%, and 16.9%, respectively. Higher (lower) ratios for the three inequivalent SiGa sites may come from a lower (higher) formation energy. The Tetra (Octa) SiGa site has the highest (lowest) ratio of the three SiGa sites since it has the lowest (highest) formation energy. We suggest that the tetrahedral SiGa site is due to the active dopant site, whereas the pentahedral and octahedral SiGa sites can be attributed to the inactive dopant sites for Si-doped κ-Ga2O3(001).

Structural and Photoelectronic Properties of κ-Ga2O3 Thin Films Grown on Polycrystalline Diamond Substrates.

Orthorhombic κ-Ga2O3 thin films were grown for the first time on polycrystalline diamond free-standing substrates by metal-organic vapor phase epitaxy at a temperature of 650 °C. Structural, morphological, electrical, and photoelectronic properties of the obtained heterostructures were evaluated by optical microscopy, X-ray diffraction, current-voltage measurements, and spectral photoconductivity, respectively. Results show that a very slow cooling, performed at low pressure (100 mbar) under a controlled He flow soon after the growth process, is mandatory to improve the quality of the κ-Ga2O3 epitaxial thin film, ensuring a good adhesion to the diamond substrate, an optimal morphology, and a lower density of electrically active defects. This paves the way for the future development of novel hybrid architectures for UV and ionizing radiation detection, exploiting the unique features of gallium oxide and diamond as wide-bandgap semiconductors.

Interfacial Properties of the SnO/κ-Ga2O3 p-n Heterojunction: A Case of Subsurface Doping Density Reduction via Thermal Treatment in κ-Ga2O3.

The interfacial properties of a planar SnO/κ-Ga2O3 p-n heterojunction have been investigated by capacitance-voltage (C-V) measurements following a methodological approach that allows consideration of significant combined series resistance and parallel leakage effects. Single-frequency measurements were carried out in both series- and parallel-model measurement configurations and then compared to the dual-frequency approach, which permits us to evaluate the depletion capacitance of diode independently of leakage conductance and series resistance. It was found that in the bias region, where the dissipation factor was low enough, they give the same results and provide reliable experimental C-V data. The doping profile extracted from the C-V data shows a nonuniformity at the junction interface that was attributed to a depletion of subsurface net donors at the n-side of the diode. This attribution was corroborated by doping profiles and carrier distributions in the n and p sides of the heterojunction obtained from the simulation of the measured C-V data by the Synopsys Sentaurus-TCAD suite. Hall effect measurements and Hg-probe C-V investigation on single κ-Ga2O3 layers, either as-grown or submitted to thermal treatments, support the hypothesis of the subsurface donor reduction during the SnO deposition. This study can shed light on the subsurface doping density variation in κ-Ga2O3 due to high-temperature treatment. The investigation of the SnO/κ-Ga2O3 heterointerface provides useful hints for the fabrication of diodes based on κ-Ga2O3. The methodological approach presented here is of general interest for reliable characterization of planar diodes.

Electrical properties and chemiresistive response to 2,4,6 trinitrotoluene vapours of large area arrays of Ge nanowires.

We study the electrical and morphological properties of random arrays of Ge nanowires (NW) deposited on sapphire substrates. NW-based devices were fabricated with the aim of developing chemiresistive-type sensors for the detection of explosive vapours. We present the results obtained on pristine and annealed NWs and, focusing on the different phenomenology observed, we discuss the critical role played by NW-NW junctions on the electrical conduction and sensing performances. A mechanism is proposed to explain the high efficiency of the annealed arrays of NWs in detecting 2,4,6 trinitrotoluene vapours. This study shows the promising potential of Ge NW-based sensors in the field of civil security.

Selection and Functionalization of Germanium Nanowires for Bio-Sensing.

In this paper, we investigate the use of dielectrophoresis to align germanium nanowire arrays to realize nanowire-based diodes and their subsequent use for bio-sensing. After establishing that dielectrophoresis is a controllable and repeatable fabrication method to create devices from germanium nanowires, we use the optimum process conditions to form a series of diodes. These are subsequently functionalized with an aptamer, which is able to bind specifically to the spike protein of SARS-Cov2 and investigated as a potential sensor. We observe a linear increase in the source to drain current as the concentration of spike protein is increased from 100 fM/L to 1 nM/L.

Detection of Nitroaromatic Explosives in Air by Amino-Functionalized Carbon Nanotubes.

Nitroaromatic explosives are the most common explosives, and their detection is important to public security, human health, and environmental protection. In particular, the detection of solid explosives through directly revealing the presence of their vapors in air would be desirable for compact and portable devices. In this study, amino-functionalized carbon nanotubes were used to produce resistive sensors to detect nitroaromatic explosives by interaction with their vapors. Devices formed by carbon nanotube networks working at room temperature revealed trinitrotoluene, one of the most common nitroaromatic explosives, and di-nitrotoluene-saturated vapors, with reaction and recovery times of a few and tens of seconds, respectively. This type of resistive device is particularly simple and may be easily combined with low-power electronics for preparing portable devices.

A Review on Chemical Vapour Deposition of Two-Dimensional MoS2 Flakes.

Two-dimensional (2D) materials such as graphene, transition metal dichalcogenides, and boron nitride have recently emerged as promising candidates for novel applications in sensing and for new electronic and photonic devices. Their exceptional mechanical, electronic, optical, and transport properties show peculiar differences from those of their bulk counterparts and may allow for future radical innovation breakthroughs in different applications. Control and reproducibility of synthesis are two essential, key factors required to drive the development of 2D materials, because their industrial application is directly linked to the development of a high-throughput and reliable technique to obtain 2D layers of different materials on large area substrates. Among various methods, chemical vapour deposition is considered an excellent candidate for this goal thanks to its simplicity, widespread use, and compatibility with other processes used to deposit other semiconductors. In this review, we explore the chemical vapour deposition of MoS2, considered one of the most promising and successful transition metal dichalcogenides. We summarize the basics of the synthesis procedure, discussing in depth: (i) the different substrates used for its deposition, (ii) precursors (solid, liquid, gaseous) available, and (iii) different types of promoters that favour the growth of two-dimensional layers. We also present a comprehensive analysis of the status of the research on the growth mechanisms of the flakes.

Germanium Nanowires as Sensing Devices: Modelization of Electrical Properties.

In this paper, we model the electrical properties of germanium nanowires with a particular focus on physical mechanisms of electrical molecular sensing. We use the Tibercad software to solve the drift-diffusion equations in 3D and we validate the model against experimental data, considering a p-doped nanowire with surface traps. We simulate three different types of interactions: (1) Passivation of surface traps; (2) Additional surface charges; (3) Charge transfer from molecules to nanowires. By analyzing simulated I-V characteristics, we observe that: (i) the largest change in current occurs with negative charges on the surfaces; (ii) charge transfer provides relevant current changes only for very high values of additional doping; (iii) for certain values of additional n-doping ambipolar currents could be obtained. The results of these simulations highlight the complexity of the molecular sensing mechanism in nanowires, that depends not only on the NW parameters but also on the properties of the molecules. We expect that these findings will be valuable to extend the knowledge of molecular sensing by germanium nanowires, a fundamental step to develop novel sensors based on these nanostructures.

Direct growth of germanium nanowires on glass.

We report a detailed characterization of Ge NWs directly grown on glass by a MOVPE system, showing how different growth parameters can affect the final outcome and comparing NWs grown on a monocrystalline Ge(111) substrate with NWs grown on amorphous glass. Our experimental results indicate that the choice of the substrate does not affect any of the relevant morphological, crystallographic or electrical properties of Ge NWs. Lengths are in the 20-30 micrometer range with minimal tapering, while growth rates are very similar to to NWs grown on Ge(111); TEM and Raman characterization show a very good crystallinity of measured nanostructures. We have also analyzed the growth process on glass and we were able to reach a conclusion on the specific growth mechanism for Ge NWs on amorphous substrates. Our findings demonstrate that glass is a valid option as cheap substrate for the mass production of these nanostructures.

Defect influence on in-plane photocurrent of InAs/InGaAs quantum dot array: long-term electron trapping and Coulomb screening.

Metamorphic InAs/In0.15Ga0.85As and InAs/In0.31Ga0.69As quantum dot (QD) arrays are known to be photosensitive in the telecommunication ranges at 1.3 and 1.55 µm, respectively; however, for photonic applications of these nanostructures, the effect of levels related to defects still needs in-depth investigation. We have focused on the influence of electron traps of defects on photocurrent (PC) in the plane of the QD array, studying by PC and deep level thermally stimulated current spectroscopy together with HRTEM and theoretical modeling. In the structures, a rich spectrum of electron trap levels of point defects EL6 (E c - 0.37 eV), EL7 (0.29-0.30 eV), EL8 (0.27 eV), EL9/M2 (0.22-0.23 eV), EL10/M1 (0.16 eV), M0 (∼0.11 eV) and three extended defects ED1/EL3 (0.52-0.54), ED2/EL4 (0.47-0.48 eV), ED3/EL5 (0.42-0.43 eV) has been identified. Among them, new defect levels undiscovered earlier in InAs/InGaAs nanostructures has been detected, in particular, EL8 and M0. The found electron traps are shown to affect a time-dependent PC at low temperatures. Besides a long-term kinetics due to trap charging, a prolonged PC decrement versus time is measured under constant illumination. The decrement is interpreted to be related to a Coulomb screening of the conductivity channel by the electrons captured in the QD interface traps. The decrement is well fitted by allometric exponents, which means many types of traps involved in electron capturing. This study provides new findings into the mechanism of in-plane PC of QD arrays, showing a crucial importance of growth-related defects on photoresponsivity at low temperatures.

Growth of germanium nanowires with isobuthyl germane.

We demonstrate the feasibility of the use of isobutyl germane, a novel germanium source, for the vapor-liquid-solid growth of germanium nanowires (NWs) on Si (111) substrates, using a thin gold layer as catalyst. The density and the diameter of the NWs were controlled by varying the Au layer thickness and the isobutyl germane flow. The NWs grow along (111) directions and show perfect crystallinity and lengths from several hundreds of nm to 3-4 µm. The use of isobutyl germane gives a considerable technological advantage in the growth of germanium NWs since it is a safer and more manageable germanium source and it allows to grow Ge NWs in a standard vapor phase epitaxy system at 400 °C.

Interband Photoconductivity of Metamorphic InAs/InGaAs Quantum Dots in the 1.3-1.55-µm Window.

Photoelectric properties of the metamorphic InAs/In x Ga1 - xAs quantum dot (QD) nanostructures were studied at room temperature, employing photoconductivity (PC) and photoluminescence spectroscopies, electrical measurements, and theoretical modeling. Four samples with different stoichiometry of In x Ga1 - xAs cladding layer have been grown: indium content x was 0.15, 0.24, 0.28, and 0.31. InAs/In0.15Ga0.85As QD structure was found to be photosensitive in the telecom range at 1.3 µm. As x increases, a redshift was observed for all the samples, the structure with x = 0.31 was found to be sensitive near 1.55 µm, i.e., at the third telecommunication window. Simultaneously, only a slight decrease in the QD PC was recorded for increasing x, thus confirming a good photoresponse comparable with the one of In0.15Ga0.75As structures and of GaAs-based QD nanostructures. Also, the PC reduction correlate with the similar reduction of photoluminescence intensity. By simulating theoretically the quantum energy system and carrier localization in QDs, we gained insight into the PC mechanism and were able to suggest reasons for the photocurrent reduction, by associating them with peculiar behavior of defects in such a type of structures. All this implies that metamorphic QDs with a high x are valid structures for optoelectronic infrared light-sensitive devices.

Bipolar Effects in Photovoltage of Metamorphic InAs/InGaAs/GaAs Quantum Dot Heterostructures: Characterization and Design Solutions for Light-Sensitive Devices.

The bipolar effect of GaAs substrate and nearby layers on photovoltage of vertical metamorphic InAs/InGaAs in comparison with pseudomorphic (conventional) InAs/GaAs quantum dot (QD) structures were studied. Both metamorphic and pseudomorphic structures were grown by molecular beam epitaxy, using bottom contacts at either the grown n +-buffers or the GaAs substrate. The features related to QDs, wetting layers, and buffers have been identified in the photoelectric spectra of both the buffer-contacted structures, whereas the spectra of substrate-contacted samples showed the additional onset attributed to EL2 defect centers. The substrate-contacted samples demonstrated bipolar photovoltage; this was suggested to take place as a result of the competition between components related to QDs and their cladding layers with the substrate-related defects and deepest grown layer. No direct substrate effects were found in the spectra of the buffer-contacted structures. However, a notable negative influence of the n +-GaAs buffer layer on the photovoltage and photoconductivity signal was observed in the InAs/InGaAs structure. Analyzing the obtained results and the performed calculations, we have been able to provide insights on the design of metamorphic QD structures, which can be useful for the development of novel efficient photonic devices.

Comparative Study of Photoelectric Properties of Metamorphic InAs/InGaAs and InAs/GaAs Quantum Dot Structures.

Optical and photoelectric properties of metamorphic InAs/InGaAs and conventional pseudomorphic InAs/GaAs quantum dot (QD) structures were studied. We used two different electrical contact configurations that allowed us to have the current flow (i) only through QDs and embedding layers and (ii) through all the structure, including the GaAs substrate (wafer). Different optical transitions between states of QDs, wetting layers, GaAs or InGaAs buffers, and defect-related centers were studied by means of photovoltage (PV), photoconductivity (PC), photoluminescence (PL), and absorption spectroscopies. It was shown that the use of the InGaAs buffer spectrally shifted the maximum of the QD PL band to 1.3 µm (telecommunication range) without a decrease in the yield. Photosensitivity for the metamorphic QDs was found to be higher than that in GaAs buffer while the photoresponses for both metamorphic and pseudomorphic buffer layers were similar. The mechanisms of PV and PC were discussed for both structures. The dissimilarities in properties of the studied structures are explained in terms of the different design. A critical influence of the defects on the photoelectrical properties of both structures was observed in the spectral range from 0.68 to 1.0 eV for contact configuration (ii), i.e., in the case of electrically active GaAs wafer. No effect of such defects on the photoelectric spectra was found for configuration (i), when the structures were contacted to the top and bottom buffers; only a 0.83 eV feature was observed in the photocurrent spectrum of pseudomorphic structure and interpreted to be related to defects close to InAs/GaAs QDs.

Two-color single-photon emission from InAs quantum dots: toward logic information management using quantum light.

In this work, we propose the use of the Hanbury-Brown and Twiss interferometric technique and a switchable two-color excitation method for evaluating the exciton and noncorrelated electron-hole dynamics associated with single photon emission from indium arsenide (InAs) self-assembled quantum dots (QDs). Using a microstate master equation model we demonstrate that our single QDs are described by nonlinear exciton dynamics. The simultaneous detection of two-color, single photon emission from InAs QDs using these nonlinear dynamics was used to design a NOT AND logic transference function. This computational functionality combines the advantages of working with light/photons as input/output device parameters (all-optical system) and that of a nanodevice (QD size of ∼ 20 nm) while also providing high optical sensitivity (ultralow optical power operational requirements). These system features represent an important and interesting step toward the development of new prototypes for the incoming quantum information technologies.